The case in front of me: 98.8% · oral semaglutide · QSC.
The failure mode I am trying to avoid is making this decision emotionally.
I have twelve months in view and I would like the plan to survive that long.
What should I decide now, and what should I defer?
On the detail: the short answer is that two competent laboratories on identical material will disagree, and the disagreement is almost always explainable by method differences.
Tailing factor measures peak shape, and a badly tailing peak spreads into the region where small impurities live, forcing tangent-skim integration that assigns tail area to the main peak.
| Δ mass (Da) | Most likely cause | Distinguishing feature |
|---|---|---|
| +1 | Deamidation (Asn or Gln) | New peak, slightly earlier retention |
| −17 | Loss of ammonia | Often with deamidation |
| −18 | Dehydration / succinimide | pH-dependent, reversible |
| +16 | Oxidation (Met, Trp) | Earlier retention, light-related |
| −128 | Missing Gln or Lys | Deletion sequence from synthesis |
| 0 | Isomer: racemisation or scrambling | Same mass, shifted retention |
The underlying point is that column pore size affects mass transfer — a 100 Angstrom packing on a 5 kDa peptide restricts diffusion, broadening the peak and potentially hiding small impurities in the shoulders.
Proline conformer interconversion kinetics are well-characterised and the half-life is of the same order as the chromatographic peak width at room temperature.
I would be careful about over-reading a single measurement — treat it as a data point, not as ground truth.
Compare purity within a single laboratory on the same method, never across laboratories.
Analytical standards and reagents with traceable certificates. Every quantitative result you read inherits the accuracy of the standard behind it.
Shop standardsPurity is a method-dependent figure, and that is not a limitation of the measurement, it is a property of what the measurement actually answers.
Retention time is sequence-specific and method-specific, so comparing your result to a supplier value using a different method is meaningless without method documentation.
Buffer versus acid in the mobile phase changes the ionisation state of basic and acidic residues, shifting retention and selectivity — same vial, potentially different separation.
Inter-laboratory studies on identical peptide material routinely find half-a-per-cent to a full-per-cent spreads in reported purity on the same sample.
Worth noting that method standardisation is poor in the research-grade space compared to pharmaceutical work, so identical-looking methods can produce different results.
The practical summary: ask for the chromatogram and the method, and ignore the headline number until you have both.
Identity and purity are orthogonal, and a high purity says almost nothing about whether the peak is actually what you think it is.
Integration of the shoulder — whether you use perpendicular drop or tangent skim — determines what area gets assigned to the main peak versus the impurity table.
The underlying point is that the fraction of your main peak that is actually your target versus isomers, fragments or related sequences is invisible without complementary identity testing.
The Arrhenius relationship for peptide degradation is the basis of accelerated stability testing and also governs how quickly methods drift with temperature.
The limitation is that single-digit micro-impurities become invisible at typical reporting thresholds, so "no impurities detected" means "none above one in two thousand."
If you are ranking vendors, specify a method and have all samples tested at the same place.
The honest answer is that the achievable range of plausible purity figures for a given vial is wider than most people expect.
Mass on column affects detector linearity and peak overlap — overloading broadens peaks and hides neighbours, while underloading improves resolution but loses sensitivity.
Published side-by-side method comparisons show that a two-point difference in purity on the same vial is easily explained by method choice alone.
The caveat is that purity without identity is only half an answer — a high purity does not mean the peak is actually what you think it is.
Compare purity within a single laboratory on the same method, never across laboratories.
More usefully, gradient slope is the most powerful parameter and almost nobody mentions it, which is why two reports on the same material disagree by a point.
Mobile phase additive choice affects ionisation and peak shape — TFA gives sharp peaks but suppresses mass spectrometry signal, formic acid gives worse peaks but preserves signal.
One qualification: achieving purity above roughly 98 per cent on a 30-residue peptide is fighting the chemistry of synthesis, not the quality of the purification.
The practical summary: ask for the chromatogram and the method, and ignore the headline number until you have both.
Ask PeptideStack is a static archive. Posting is closed, but the norms are worth stating: answer the question that was asked, show your working, cite the trial or the certificate, and say plainly where the evidence runs out.