The specifics, since they change the answer: VendorInvestigate · 95.2%.
Something has gone wrong and I would like to know how badly before I decide what to do.
Nothing else in the setup changed, which is what makes this puzzling.
What is the differential here, and which test discriminates between the options?
Purity is a method-dependent figure, and that is not a limitation of the measurement, it is a property of what the measurement actually answers.
Tailing factor measures peak shape, and a badly tailing peak spreads into the region where small impurities live, forcing tangent-skim integration that assigns tail area to the main peak.
| Test | Answers | Does NOT answer |
|---|---|---|
| RP-HPLC, area % | What fraction of detected material is the target | How much target is present |
| Quantified content | Milligrams of peptide per vial | What the impurities are |
| ESI-MS identity | Whether the molecular weight matches | Purity, or isomeric substitution |
| Peptide mapping | Sequence, localised to a fragment | Quantity |
| Karl Fischer | Water content of the solid | Solvent content |
| LAL endotoxin | Pyrogen load in EU/mg | Sterility |
| Sterility test | Growth in defined media over 14 days | Endotoxin, or bioburden count |
Mobile phase additive choice affects ionisation and peak shape — TFA gives sharp peaks but suppresses mass spectrometry signal, formic acid gives worse peaks but preserves signal.
The Arrhenius relationship for peptide degradation is the basis of accelerated stability testing and also governs how quickly methods drift with temperature.
The practical summary: ask for the chromatogram and the method, and ignore the headline number until you have both.
Analytical standards and reagents with traceable certificates. Every quantitative result you read inherits the accuracy of the standard behind it.
Shop standardsStart from what the detector sees, because that tells you what the number means.
The fraction of your main peak that is actually your target versus isomers, fragments or related sequences is invisible without complementary identity testing.
Worth being precise here: mass on column affects detector linearity and peak overlap — overloading broadens peaks and hides neighbours, while underloading improves resolution but loses sensitivity.
If you are ranking vendors, specify a method and have all samples tested at the same place.
The short answer is that two competent laboratories on identical material will disagree, and the disagreement is almost always explainable by method differences.
Detection wavelength matters because 214 nm sees the peptide backbone while 280 nm sees only aromatic side chains — so truncation impurities lacking a tryptophan are invisible at 280 nm.
Integration of the shoulder — whether you use perpendicular drop or tangent skim — determines what area gets assigned to the main peak versus the impurity table.
Proline conformer interconversion kinetics are well-characterised and the half-life is of the same order as the chromatographic peak width at room temperature.
Compare purity within a single laboratory on the same method, never across laboratories.
Read the chromatogram before you read the number, because the number without the trace is not a measurement, it is a claim.
Sample solvent strength affects peak shape — if you inject in strong solvent on a gradient starting in weak solvent, the solvent peak can distort your main peak or create a false shoulder.
The caveat is that purity without identity is only half an answer — a high purity does not mean the peak is actually what you think it is.
The practical summary: ask for the chromatogram and the method, and ignore the headline number until you have both.
edited 14 Oct 2025 by aine_mulcahy — expanded the table to cover the lower concentration
Concretely, the method matters more than the vial, which is why specifying a method buys you far more than changing suppliers does.
Retention time is sequence-specific and method-specific, so comparing your result to a supplier value using a different method is meaningless without method documentation.
Published side-by-side method comparisons show that a two-point difference in purity on the same vial is easily explained by method choice alone.
Worth noting that method standardisation is poor in the research-grade space compared to pharmaceutical work, so identical-looking methods can produce different results.
If you are ranking vendors, specify a method and have all samples tested at the same place.
Ask PeptideStack is a static archive. Posting is closed, but the norms are worth stating: answer the question that was asked, show your working, cite the trial or the certificate, and say plainly where the evidence runs out.