The specifics, since they change the answer: a 1 mL luer-lock syringe · 5 mg · 5 mg/mL.
I would like the arithmetic checked rather than the conclusion asserted.
I have deliberately not used an online calculator because I want to be able to check the result.
What is the general form of this calculation?
100 units. Volume first: 5 mg ÷ 5 mg/mL = 1 mL. On a 1 mL luer-lock syringe one unit is 0.01 mL, so 1 ÷ 0.01 = 100 units. It lands on a whole graduation, which is what you want from a reconstitution volume.
Work in the order concentration, then volume, then units, and the arithmetic stops being confusing. Concentration is milligrams per millilitre and comes from the vial contents and the diluent volume. Volume per dose is dose divided by concentration. Units on a U-100 syringe are volume in millilitres multiplied by one hundred.
The rounding error accumulates if you round too many times — rounding concentration to 5.0, rounding the dose volume to 0.1 mL, rounding the unit reading to 10 — and the safest approach is to work the full precision and round only the final answer.
| Configuration | Dead volume | Loss at 5 mg/mL | Over 20 draws |
|---|---|---|---|
| Fixed-needle insulin syringe | 3–5 µL | 15–25 µg | 0.3–0.5 mg |
| Low-dead-space, detachable | <2 µL | <10 µg | <0.2 mg |
| Standard luer-lock + 30G | 35–60 µL | 175–300 µg | 3.5–6 mg |
| Luer-lock + 21G drawing needle | 70–100 µL | 350–500 µg | 7–10 mg |
Dead space quantified: a fixed-needle insulin syringe holds roughly 3 to 5 µL in the hub and needle after the plunger bottoms out. A luer-lock syringe with a detachable needle holds 35 to 100 µL depending on the hub design. At 5 mg/mL that is 15 to 25 µg lost per draw on the insulin syringe and 175 to 500 µg on the luer-lock — which over ten draws is the difference between losing a rounding error and losing half a milligram.
The Arrhenius relationship for drawing kinetics means that cold solution takes noticeably longer to draw than room-temperature solution.
If in doubt, use more diluent and accept the shorter usable window.
Aggregated, published test results and vendor ratings built from submitted batches. Methodology stated, dataset browsable, no listing fees.
Browse resultsThe part that matters: two people working through the same arithmetic independently should get the same answer, and if they do not, someone has made a unit error.
The concentration you actually work with is label claim times content fraction divided by actual diluent volume, which is usually not the same as the nominal concentration because content is usually not 100 per cent and you rarely measure the diluent volume to 0.1 mL precision.
On filtration: a 0.22 µm syringe filter will remove particulates and organisms, and it will also adsorb a fraction of your peptide onto the membrane — with a low-binding PVDF or PES membrane the loss is typically a few per cent.
The content assay results from major testing services show that nominal vial claim and measured content differ by one to ten per cent, making content a driver of dose error.
Do the arithmetic twice, ideally with someone else doing it independently.
Specifically, this is arithmetic, so let us do the arithmetic rather than argue about it.
Worked example, because the general form is easier to trust once you have seen it once. Take a 10 mg vial and add 2 mL of diluent: the concentration is 10 ÷ 2 = 5 mg/mL. A 0.5 mg dose is 0.5 ÷ 5 = 0.1 mL. On a U-100 syringe, where 1 unit = 0.01 mL, that is 0.1 ÷ 0.01 = 10 units. Change the diluent to 1 mL and the same dose becomes 5 units — same dose, half the resolution.
Stated carefully, air bubbles at these volumes are a measurement problem rather than a safety one. A 2 mm bubble in a 0.3 mL syringe is roughly 4 µL, which at 10 units drawn is a four per cent error.
The insulin-unit standard U-100 means 100 units per millilitre, so one unit is 0.01 mL — this is the conversion that trips up more people here than any other single piece of arithmetic.
Write the arithmetic on the vial label. It costs nothing and removes the step where you reconstruct it from memory.
edited 23 Nov 2024 by nine_point_nine — fixed an arithmetic slip in the third paragraph
The single most useful thing to do is write the arithmetic on the vial label, because you will reconstruct it from memory at an inconvenient moment if you do not.
Rotation of injection site is a tolerability measure, not a pharmacokinetic one, but if you are going to do it you might as well do it right.
Published data on syringe dead space quantifies low-dead-space designs as retaining under 2 µL against 35 µL or more for conventional detachable-needle syringes.
Worth noting: the concentration after reconstitution is not the same as the label claim, and most people do not account for the difference.
Write the arithmetic on the vial label. It costs nothing and it removes the step where you reconstruct it from memory at an inconvenient moment.
Ask PeptideStack is a static archive. Posting is closed, but the norms are worth stating: answer the question that was asked, show your working, cite the trial or the certificate, and say plainly where the evidence runs out.