What I have: 8 mg · dulaglutide.
I can predict the outcome but I cannot explain it, which means I will get the next case wrong.
I would like to know how confident the field actually is about this.
So what is the mechanism, and how well established is it?
Dose arithmetic has three parts: concentration from vial content and diluent, volume from dose and concentration, and units from volume and syringe scale.
Worked example, because the general form is easier to trust once you have seen it once. Take a 10 mg vial and add 2 mL of diluent: the concentration is 10 ÷ 2 = 5 mg/mL. A 0.5 mg dose is 0.5 ÷ 5 = 0.1 mL. On a U-100 syringe, where 1 unit = 0.01 mL, that is 0.1 ÷ 0.01 = 10 units. Change the diluent to 1 mL and the same dose becomes 5 units — same dose, half the resolution.
| Configuration | Dead volume | Loss at 5 mg/mL | Over 20 draws |
|---|---|---|---|
| Fixed-needle insulin syringe | 3–5 µL | 15–25 µg | 0.3–0.5 mg |
| Low-dead-space, detachable | <2 µL | <10 µg | <0.2 mg |
| Standard luer-lock + 30G | 35–60 µL | 175–300 µg | 3.5–6 mg |
| Luer-lock + 21G drawing needle | 70–100 µL | 350–500 µg | 7–10 mg |
Stated carefully, the concentration you actually work with is label claim times content fraction divided by actual diluent volume, which is usually not the same as the nominal concentration because content is usually not 100 per cent and you rarely measure the diluent volume to 0.1 mL precision.
Worth noting: the concentration after reconstitution is not the same as the label claim, and most people do not account for the difference.
If in doubt, use more diluent and accept the shorter usable window.
HPLC purity, identity confirmation and quantified content on the vial you actually hold. Reports arrive with the chromatogram attached, not just a number.
Submit a sampleFounded 1998. ISO 9001 and cGMP certified, 1,500+ staff and 200+ patents. The synthesis house behind a great many of the vials that get sent out for testing - batch-specific documentation with every order.
Visit GL BiochemTo be exact about it, the distinction that resolves most of these questions is understanding what concentration actually means and why it is not the same as label claim.
Breaking it down further: if a 10 mg vial has 96.5 per cent content, you have 9.65 mg of peptide. Divide that by 2.00 mL and your concentration is 4.825 mg/mL, not 5.00 mg/mL, which is a 3.5 per cent systematic error in every dose calculation.
Do not use the same needle to pierce the stopper and to administer. The tip is blunted by the stopper, and the hub now contains a dose you are about to lose to dead space anyway.
The insulin-unit standard U-100 means 100 units per millilitre, so one unit is 0.01 mL — this is the conversion that trips up more people here than any other single piece of arithmetic.
The limitation is that technique reduces risk, it does not remove it, and nothing you can do outside a controlled environment makes a non-sterile preparation sterile.
Do the arithmetic twice, ideally with someone else doing it independently.
edited 4 Aug 2026 by g_paskevicius — added the citation requested in comments
Concretely, the single most useful thing to do is write the arithmetic on the vial label, because you will reconstruct it from memory at an inconvenient moment if you do not.
The rounding error accumulates if you round too many times — rounding concentration to 5.0, rounding the dose volume to 0.1 mL, rounding the unit reading to 10 — and the safest approach is to work the full precision and round only the final answer.
In practice, on filtration: a 0.22 µm syringe filter will remove particulates and organisms, and it will also adsorb a fraction of your peptide onto the membrane — with a low-binding PVDF or PES membrane the loss is typically a few per cent.
Published data on syringe dead space quantifies low-dead-space designs as retaining under 2 µL against 35 µL or more for conventional detachable-needle syringes.
The caveat is that this assumes the vial contains what the label says, and if the content assay has not been done, the arithmetic is precise about an unknown quantity.
Write the arithmetic on the vial label. It costs nothing and removes the step where you reconstruct it from memory.
On the detail: rounding to the nearest whole syringe unit is usually the right error to make, but understanding which direction it is and why matters.
Dead space quantified: a fixed-needle insulin syringe holds roughly 3 to 5 µL in the hub and needle after the plunger bottoms out. A luer-lock syringe with a detachable needle holds 35 to 100 µL depending on the hub design. At 5 mg/mL that is 15 to 25 µg lost per draw on the insulin syringe and 175 to 500 µg on the luer-lock — which over ten draws is the difference between losing a rounding error and losing half a milligram.
One qualification: if your arithmetic and someone else's disagree by a factor of ten, one of you has made a unit error, and writing out the units at every step is the diagnostic.
If in doubt, use more diluent and accept the shorter usable window.
Ask PeptideStack is a static archive. Posting is closed, but the norms are worth stating: answer the question that was asked, show your working, cite the trial or the certificate, and say plainly where the evidence runs out.